16. When the show cdp neighbors command is issued from Router C, which devices will be displayed in the output?
D, SWH-2A, B, D
SWH-1, SWH-2
B, D
SWH-1, A, B
A, B, D, SWH-1, SWH-2
17. Refer to the exhibit. A network administrator is trying to determine why router JAX has no OSPF routes in its routing table. All routers are configured for OSPF area 0. From the JAX router, the administrator is able to ping its connected interfaces and the Fa0/1 interface of the ORL router but no other router interfaces. What is a logical step that the network administrator should take to troubleshoot the problem?
Reboot the routers.Change the OSPF process ID on all of the routers to 0.
Check to see if the cable is loose between ORL and JAX.
Check to see if CDP packets are passing between the routers.
Use show and debug commands to determine if hellos are propagating.
18. Using default settings, what is the next step in the router boot sequence after the IOS loads from flash?
Perform the POST routine.Search for a backup IOS in ROM.
Load the bootstrap program from ROM.
Load the running-config file from RAM.
Locate and load the startup-config file from NVRAM.
19. Refer to the exhibit. What summary address can Router2 advertise to Router1 to reach the three networks on Routers 3, 4, and 5 without advertising any public address space or overlapping the networks on Router1?
172.16.0.0/8172.16.0.0/10
172.16.0.0/13
172.16.0.0/20
172.16.0.0/24
20. The network shown in the diagram is having problems routing traffic. It is suspected that the problem is with the addressing scheme. What is the problem with the addressing used in the topology?
The address assigned to the Ethernet0 interface of Router1 is a broadcast address for that subnetwork.
The subnetwork configured on the serial link between Router1 and Router2 overlaps with the subnetwork assigned to Ethernet0 of Router3.
The subnetwork assigned to the Serial0 interface of Router1 is on a different subnetwork from the address for Serial0 of Router2.
The subnetwork assigned to Ethernet0 of Router2 overlaps with the subnetwork assigned to Ethernet0 of Router3.
21. Refer to the exhibit. A new PC was deployed in the Sales network. It was given the host address of 192.168.10.31 with a default gateway of 192.168.10.17. The PC is not communicating with the network properly. What is the cause?
The address is in the wrong subnet.
192.168.10.31 is the broadcast address for this subnet.
The default gateway is incorrect.
The host address and default gateway are swapped.
22. Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statement is true regarding how the routers in this topology will respond to this event?
Router4 will learn about the failed route 30 seconds later in the next periodic update.
Split horizon will prevent Router4 from forwarding packets to the 10.0.0.0 network until the holddown timer expires.
Router5 immediately flushes the unreachable route from its routing table.
Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.
23. Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.)
The route to network 172.16.0.0 has an AD of 156160.
Network 192.168.0.16 can best be reached using FastEthernet0/0.
The AD of EIGRP routes has been manually changed to a value other than the default value.
Router1 is running both the EIGRP and OSPF routing process.
Network 172.17.0.0 can only be reached using a default route.
No default route has been configured.
24. Refer to the exhibit. What is the most efficient summarization of the routes attached to router R1?
198.18.0.0/16
198.18.48.0/21
198.18.32.0/22
198.18.48.0/23
198.18.49.0/23
198.18.52.0/22
25. What is the purpose of the TTL field within an IP packet header?
clears an unreachable route from the routing table after the invalid timer expires.
prevents regular update messages from inappropriately reinstating a route that may have gone bad.
removes an unreachable route from the routing table after the flush timer expires.
limits the period of time or number of hops a packet can traverse through the network before it should be discarded.
used to mark the route as unreachable in a routing update that is sent to other routers.
26. Refer to exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.)
Paris(config)# router eigrp 100
Paris(config)# router eigrp
Paris(config-router)# network 192.168.6.0
Paris(config-router)# network 192.168.7.0
Paris(config-router)# network 192.168.8.0
Paris(config-router)# network 192.168.9.0
27. What does RIP use to reduce convergence time in a larger network?
It reduces the update timer to 15 seconds if there are more then 10 routes.
It uses triggered updates to announce network changes if they happen in between the periodic updates.
It uses random pings to detect if a pathway is down and therefore is preemptive on finding networks that are down.
It uses multicast instead of broadcast to send routing updates.
28. Refer to the exhibit. What two statements are true based on the output shown? (Choose two.)
the reported distance to network 172.16.1.0 is 217241
192.168.10.5 and 192.168.10.9 are feasible successors
neighbors 192.168.10.9 and 192.168.10.5 have auto summary disabled
router 3 is load balancing traffic to the 172.16.3.0 network across its serial interfaces
all interfaces shown on Router3 are in the passive state and will not send EIGRP advertisements
29. Refer to the exhibit. The network is using the RIPv2 routing protocol. If network 10.0.0.0 goes down, what mechanism will prevent Router1 from advertising false routing information back to Router2?
triggered updates
poison reverse
holddown timers
split horizon
30. What is the function of the OSPF LSU packet?
used to confirm receipt of certain types of OSPF packets
used to establish and maintain adjacency with other OSPF routers
used to request more information about any entry in the BDR
used to announce new OSPF information and to reply to certain types of requests
21. Refer to the exhibit. A new PC was deployed in the Sales network. It was given the host address of 192.168.10.31 with a default gateway of 192.168.10.17. The PC is not communicating with the network properly. What is the cause?
The address is in the wrong subnet.
192.168.10.31 is the broadcast address for this subnet.
The default gateway is incorrect.
The host address and default gateway are swapped.
22. Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statement is true regarding how the routers in this topology will respond to this event?
Router4 will learn about the failed route 30 seconds later in the next periodic update.
Split horizon will prevent Router4 from forwarding packets to the 10.0.0.0 network until the holddown timer expires.
Router5 immediately flushes the unreachable route from its routing table.
Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.
23. Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.)
The route to network 172.16.0.0 has an AD of 156160.
Network 192.168.0.16 can best be reached using FastEthernet0/0.
The AD of EIGRP routes has been manually changed to a value other than the default value.
Router1 is running both the EIGRP and OSPF routing process.
Network 172.17.0.0 can only be reached using a default route.
No default route has been configured.
24. Refer to the exhibit. What is the most efficient summarization of the routes attached to router R1?
198.18.0.0/16
198.18.48.0/21
198.18.32.0/22
198.18.48.0/23
198.18.49.0/23
198.18.52.0/22
25. What is the purpose of the TTL field within an IP packet header?
clears an unreachable route from the routing table after the invalid timer expires.
prevents regular update messages from inappropriately reinstating a route that may have gone bad.
removes an unreachable route from the routing table after the flush timer expires.
limits the period of time or number of hops a packet can traverse through the network before it should be discarded.
used to mark the route as unreachable in a routing update that is sent to other routers.
26. Refer to exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.)
Paris(config)# router eigrp 100
Paris(config)# router eigrp
Paris(config-router)# network 192.168.6.0
Paris(config-router)# network 192.168.7.0
Paris(config-router)# network 192.168.8.0
Paris(config-router)# network 192.168.9.0
27. What does RIP use to reduce convergence time in a larger network?
It reduces the update timer to 15 seconds if there are more then 10 routes.
It uses triggered updates to announce network changes if they happen in between the periodic updates.
It uses random pings to detect if a pathway is down and therefore is preemptive on finding networks that are down.
It uses multicast instead of broadcast to send routing updates.
28. Refer to the exhibit. What two statements are true based on the output shown? (Choose two.)
the reported distance to network 172.16.1.0 is 217241
192.168.10.5 and 192.168.10.9 are feasible successors
neighbors 192.168.10.9 and 192.168.10.5 have auto summary disabled
router 3 is load balancing traffic to the 172.16.3.0 network across its serial interfaces
all interfaces shown on Router3 are in the passive state and will not send EIGRP advertisements
29. Refer to the exhibit. The network is using the RIPv2 routing protocol. If network 10.0.0.0 goes down, what mechanism will prevent Router1 from advertising false routing information back to Router2?
triggered updates
poison reverse
holddown timers
split horizon
30. What is the function of the OSPF LSU packet?
used to confirm receipt of certain types of OSPF packets
used to establish and maintain adjacency with other OSPF routers
used to request more information about any entry in the BDR
used to announce new OSPF information and to reply to certain types of requests
0 komentar:
Posting Komentar